Shop

ZERO PRESSURE STYLE

16″ BETWEEN FRAME

• 1.9″ X 16 GA. GALVANIZED ROLLERS W/ ABEC

BEARINGS

• ROLLERS SET 1/4″ HIGH ON 2″ CENTERS, DRIVEN BY

HIGH TENSION BLUE URETHANE BANDS

• 7″ X 2″ X 12 GA. FORMED MILD STEEL CHANNEL

FRAMES W/ LEXAN COVERS

• BOLTED CONSTRUCTION, POWDER COATED GLOSS

WHITE

• 120 FEET PER MINUTE

• 24VDC CSA RATED POWER SUPPLY:

460VAC/3PH/60HZ, 24VDC OUTPUT: (1) 20 AMP

• (1) ENTRY ZONE WAKEUP PHOTO EYE

• (5) 24″ ACCUMULATION ZONES W/ FLAT MOTOR AND

PHOTO EYE **(5) TOTAL UL RATED DRIVER CARDS**

• POWER DISTRIBUTION CABLING INCLUDED

• H-STYLE FLOOR SUPPORTS FOR 27″ TOP OF ROLLER

• 2″ TALL, 12 GA. FIXED ANGLE SIDE GUIDES BOTH

SIDES

Features:

• Width (between rail): ranges from 13″ to 39″ in 1″ increments
• Width (overall): 3″ greater than BFR
• Length: 120 ft per driven section with drive at the center
• Rods and turnbuckles are used on every other bed section on lengths exceeding 30 ft. – this insures proper alignment of bed rollers and correct product tracking
• Rollers: 1.9″ x 16 gauge galvanized tube on 3″ centers (typical)
• Accumulation zone: 24″ long is standard – 18″, 30″ and 36″ zone lengths available – each zone is controlled by air logic
• OmniMetalCraft FM 24 volt flat motor driven roller conveyor for handling empty cases
• Zero pressure style
• Straights – 1.9″ x 16 gauge galvanized rollers with ABEC bearings on 2″ centres for safety
• Curves – 1-1/2″ diameter tapered to 1″ diameter zinc plated rollers on 2-3/16″ centres at centerline with sealed, greased bearings
• Consists of (1)10′-0″ straight, (5) zones,
• Rollers set 1/4″ high on 2″ centres driven by high tension blue urethane bands
• 120 feet per minute
• (1) Entry zone wake-up photo eye
• (9) 24″ or greater accumulation zones w/ flat motor, and photo eye, **(9) total driver cards**
• Power distribution cabling included
• “H” style floor supports – adjustable
• Fixed angle side guide – 2″ high sides located on both sides along entire length
• Drive boards include mprovision for ethernet connectivity for remote control
• 460 VAC / 3 phase / 20 amp power supply – CSA approved
• Bearings: tread rollers have pre-lubricated ball bearings – drive shaft has sealed, pre- lubricated, self- aligning cast iron ball bearings with eccentric lock collar
• Speed reduction: sealed worm gear “c” face speed reducer – number# 50 roller chain to drive
• Conveying speed: constant speeds available from 45 to 120 fpm – high speed enhancements available
• Air requirements: minimum 30 PSI on main air supply line
• Filter/regulator: supplied for main air supply line – 3/8 in. NPT port
• Motor: powered with 1/2 Hp to 2 Hp, totally enclosed, fan cooled, “c” face
• Guard rails: various ranging from solid side formed angles to adjustable formed channel
• Drive: mounted underneath with a minimum 23-1/4″ top of roller – if between frame dimension is less than 20″, motor will extend beyond frame of conveyor – side mounted drives are available with a minimum 12-3/4″ top of roller

Specifications:

Load:

• Load capacity: 1.9″ diameter maximum load – 15 pounds per driven roller – maximum driven length with single drive at center – 120 ft – 1-3/8″ diameter maximum load – 10 pounds per driven roller – maximum driven length with single drive at center – 70 feet for 1-3/8″ rollers

Structure:

• Finish: powder coated with an available range of RAL colours
• Frame: bolted construction, 7″ x 2″ x 12 gauge formed mild steel channel frames with polycarbonate covers
• Stands: supplied with adjustable “H” type supports on nominal 10 ft centers

Electrical Requirements:

• 120V 1 phase, 230 V 1 phase, 230/460V 3 phase and 575V 3 phase
• Electrical controls: Typically, a 24 VDC solenoid valve in discharge zone to override air logic – limit switch is also supplied to revert control back to air logic once the product is clear

Options:

• Electrical controls
• Guide rails of various types
• Conveyor speed